Looking for an answer to the question: Are 8 foot 2x4 actually 8 feet? On this page, we have gathered for you the most accurate and comprehensive information that will fully answer the question: Are 8 foot 2x4 actually 8 feet?
Secondly, what is the actual length of an 8 foot 2x4? x 8 ft.; Actual: 1.5 in. x 3.5 in. x 96 in. Thereof, why is a 2x4 actually 1.5x3 5? The 2x4 refers to the rough-cut green wood: it shrinks during drying, then the dried wood is planed smooth, so the finished lumber is supposed to end up at 1.5"x3. 5".
But there is a caveat will calling a 2x4 a 2x4: It’s not really two inches by four inches as its name implies. A 2x4 is actually 3-½ inches by 1-½ inches. Many of you know this, but why is this a thing?
In fact, 2x4s are never 2x4s these days. A nominal 2x4 board starts out 1.56 in. x 3.58 in. Then, the edges are surfaced (planed), reducing the actual size to 1-1/2 in. x 3-1/2 in. If boards will be kiln dried after milling, they start their lives sized 1.62 in. x 3.68 in.
Because of this extra milling, a 2x4 no longer measures a full 2 inches by four inches. Instead, a 2x4 is really only 1 1/2" by 3 1/2". Herein, how long are 2x4 at Lowes? Secondly, what is the actual length of an 8 foot 2x4? x 8 ft.; Actual: 1.5 in. x 3.5 in. x 96 in. Thereof, why is a 2x4 actually 1.5x3 5?
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
Home prices are soaring, pushed higher by a combination of record-low mortgage rates, strong demand from buyers and a lingering lack of new construction. In 2021, a new factor put pressure on home prices: Month after month, lumber prices jumped to new highs. Lumber costs soared more than 30% from January through May.
The "nominal" cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S). The nominal measurement is made before the lumber is surfaced.
6.66667 A 2x4x10 board has 6.66667 total board feet in it: the board foot factor (BFF) of a 2×4 is 0.666667.
Maybe you've noticed that lumber sizes are often misleading. The "nominal" cross-section dimensions of a piece of lumber, such as 2 X 4 or 1 X 6, are always somewhat larger than the actual, or dressed, dimensions. The reason is that dressed lumber has been surfaced or planed smooth on four sides (called S4S).
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
1.67 bd ft. 2” x 10” x 1' = 1.67 bd. ft. 2” x 12” x 1' = 2.0 bd.
Why You Should Find Studs They're always spaced either 16 or 24 inches on-center (measured from center to center) along the wall and run between the floor and ceiling. Drywall or lath (for plaster walls) attaches to the edge of the studs.
Board Foot Formula is the Most Important Lumber Calculation Accurately counting and estimating hardwood lumber is a critical calculation. ... When lumber is miscalculated, bad things happen: Customers are over charged. Clients are under charged.
The simple reason why 2×4 is not 2 inches by 4 inches is that lumber mills trim off rough or warped surfaces of a 2×4 to give it a more polished and finished look. By planning the lumber on all four sides, the original 2×4 is now reduced to 1 ½ inches by 3 1/2 inches.
Example 1: A 4/4 board 8 inches wide and 8 feet long has 5.33 bd. ft.
How Far Should A Screw Go Into A Stud? For a wood stud a screw should penetrate 1 inch into the stud for a secure hold, running a screw deeper runs the risk of hitting an electrical wire. In metal studs self-tapping screws or toggle bolts should be used.
Lumber will be strong through 2021 and this drop in lumber prices is great news for homebuilders and real estate developers alike if they choose to take advantage of their low rates now.
The iPhone beeps when its magnetometer, in the upper right of the phone, is near metal. Stud Find is an iPhone application that uses the device's built-in magnetometer to find metal studs, screws, nails and anything metallic in a wall.
The general spacing for wall studs is 16 inches on center, but they can be 24 inches. At my home, the exterior wall studs are spaced at 24-inch centers, but the interior walls are 16 inches on center.
Because of this extra milling, a 2x4 no longer measures a full 2 inches by four inches. Instead, a 2x4 is really only 1 1/2" by 3 1/2". The same is true of pine. A 1x6, for example, actually measures 3/4" x 5 1/2".
Wall studs for standard walls of 8 feet are 92 5/8 inches. In homes with 9-foot walls, the studs are 104 5/8 inches. Homes with a wall height of 10 feet use pre-cut studs at 116 5/8 inches.
A common estimate is that a contemporary, 2,000-square-foot, wood-framed, single-family house uses upwards of 16,000 board feet of framing, and about 11,000 square feet of other wood materials, such as sheathing.
The simple reason why 2×4 is not 2 inches by 4 inches is that lumber mills trim off rough or warped surfaces of a 2×4 to give it a more polished and finished look. By planning the lumber on all four sides, the original 2×4 is now reduced to 1 ½ inches by 3 1/2 inches.
Size standards, maximum moisture content, and nomenclature were agreed upon only as recently as 1964. The nominal 2x4 thus became the actual 1½ x 3½, imperceptibly, a fraction of an inch at a time.
none
2×4 – 8′ Lengths Although not quite as common as the pre-cut studs I described above, my local Home Depot has a fairly good selection of 2x4s that measure 8 feet (96”). How long is 8ft stud? 92 5/8 inches
2×4 – 8′ Lengths Although not quite as common as the pre-cut studs I described above, my local Home Depot has a fairly good selection of 2x4s that measure 8 feet (96”). These come in handy for projects where I’m building something around a 4×8 sheet of plywood.
How much does a 8 foot 2x4 cost? Consequently, how much does a 8 foot 2x4 weigh? A green-lumber 2-by-4 with a length of 8 feet weighs 13 pounds. A green-lumber 2-by-4 with a length of 12 feet weighs 20 pounds. A pressure-treated 2-by-4 …
Which means, for example, three 2x4 boards laid side by side will not measure a foot across. Because a nominal 2x4 board is really 1-1/2 inches by 3-1/2 inches. In fact, 2x4s are never 2x4s these days. A nominal 2x4 board starts out 1.56 in. x 3.58 in. Then, the edges are surfaced (planed), reducing the actual size to 1-1/2 in. x 3-1/2 in.
Similarly, what is the actual length of an 8 foot 2x4? x 8 ft.; Actual: 1.5 in. x 3.5 in. x 96 in. In respect to this, why is a 2x4 actually 1.5x3 5? The 2x4 refers to …
none
The most well-known piece of lumber is the 2x4, pronounced two-by-four. It’s mostly used in the framing of houses but you’ll also see it in just about any other construction or DIY project. But there is a caveat will calling a 2x4 a 2x4: It’s not really two inches by four inches as its name implies. A 2x4 is actually 3-½ inches by 1-½ inches.
So i was trying to figure out why some of my measurements and cuts werent lining up. Turns out all the 2x6 and 2x8 boards I got are 8' 3/8" long. I know and expect 2x4s arent actually 2x4 but I dont know if I've seen a longer length before.
Board Foot = (2 X 4 X 8) / 144. Board Foot = 64 / 144. Board Foot = 0.444444 bd ft. As you can see, this wouldn’t be an acceptable answer since you always need to get a result higher than 1. The truth is that this would be the same thing as saying that you had less than half board foot. And this simply isn’t possible.
A 4 by 8 sheet of plywood is actually 4 foot by 8 foot, exactly. It’s sold and labeled in metric, but the dimensions correspond to and are often referred to in old measures. Norway’s been metric for over a hundred years, but the labeling of lumber dimensions in metric only goes back a few decades.
When using studs, other dimensions of 2-by-4 and 2-by-6 lumber is used. Standard lengths for these range from 8 feet up to 16 feet. Why is 2×4 so expensive? Modern mills are very efficient at turning logs into 2x4s and sheets of plywood. Lumber and plywood prices are so high now because of the short-run dynamics of demand and supply. Wood demand shot up in the …
I usually use precut studs to frame 8-ft.- and 9-ft.-tall walls. Precut studs are shorter than the finished height of the wall to allow for the thickness of the bottom and top plates (the precut stud for an 8-ft. wall is actually 92-5/8 in.). A couple of years ago, precut studs were scarce locally, so I ordered a unit of ordinary 8-ft. studs.
This gives you a rough-framed wall height of 97 and 1/8 inches. Also, what is the actual length of an 8 foot 2x4? x 8 ft.; Actual: 1.5 in. x 3.5 in. x 96 in. Also, how many studs are needed for an 8 foot wall? Calculate the Studs Multiply the total wall length (in feet) by 0.75 (for 16-inch on-center stud spacing). Add three studs for each 90-degree corner.
The fence is about 62 feet long. Should I use 12 ft posts buried 4ft deep with the hole being 12 inches wide? Or should I cut posts to 11ft and bury 3 feet. I plan on filling the holes with concrete spaced about 7.5 feet apart. The wood I plan to use is pine treated 4x4s for the posts and cedar for the three 2x4 rails and the 1x6 pickets.
What you will find is that your 2 x 4 is actually 1 1/2 inches x 3-1/2 inches and that your 1 x 6 board is actually 3/4 inch x 5 1/2 inches. Actual Dimensions and Nominal Dimensions You've just run into the reality of actual lumber sizes as compared to the nominal sizes—the sizes by which they are identified in the store.
How much weight a 2×4 can hold horizontally depends on the spacing of the ceiling joists (2x4s typically aren’t strong enough to be used as a floor joist except in smaller applications, such as a shed.). An 8-foot 2×4 will bend before it breaks, so while it may hold 200 pounds, it will bow noticeably in the middle under this amount of weight.
Eventually, the actual size of a 2x4 was standardized at 1 ½" x 3 ½" to keep the dimensions consistent throughout the industry. You can read more about the history of the 2x4 here. Standard 2x4 length. 2x4 studs are typically 8 feet long, to match the standard length of a sheet of plywood or drywall. You can also find 2x4 studs that are 92 ...
But I say run it through a table saw, make 16 foot of 4x1, ( yes its not really because a 2x4 isn't) Then make a small cabinet such as a jewelry box or chest. Just my $.02. 4. level 1. Nocut12. · 7y. You could ask the people on r/woodworking. 4.
For interior walls (bearing and non) I'm wondering what the preferred method for framing might be on long walls. For example a hallway. Should I just use normal ~8' long 2x4 as top plates and stagger the top and bottom plates a few feet or is it better to buy longer top plate 2x4's to reduce the amount of joints.
@pythonian29033 A 2x4 is a common lumber in the US, approximately 2x4 inches (~5x10cm) in cross section. It's actually a bit less than that for historical/technical reasons, but close enough. They can be oriented any way you need them, though I …
Precut studs are shorter than the finished height of the wall to allow for the thickness of the bottom and top plates (the precut stud for an 8-ft. wall is actually 92-5/8 in.). A couple of years ago, precut studs were scarce locally, so I ordered a unit of ordinary 8-ft. studs.
A board foot is actually a measure of volume. By definition, a board foot is one square foot, one inch thick. To calculate board footage use the following formulas: Board Footage = width in inches x length in feet x thickness in inches. How long is an 8 foot 2x4? Specifications
Furthermore, how long is a standard 2x4 stud? The most common dimensions of wall studs are 2-by-6 and 2-by-4. Wall studs for standard walls of 8 feet are 92 5/8 inches. In homes with 9-foot walls, the studs are 104 5/8 inches. Homes with a wall height of 10 feet use pre-cut studs at 116 5/8 inches.. Also, why is a 2x4 actually 1.5x3 5?
First of all, the person complaining "these wern't 8 inches, they are 7.5" doesn't know how lumber works. Everyone knows measurements are .5 inches below, a 2x4 isn't really 2x4 etc. The second person, if you got 6ft spans, it was a shipping error, not the board's fault.
That process removes 1/2-inch from all sides of the lumber. So, what we commonly refer to as a 2×4 is actually 1.5 inches wide by 3.5 inches deep. Length. While it’s obvious to most that a 12-foot 2×4 will weigh more than an 8-foot 2×4, few know exactly how length affects weight. One foot of air-dried yellow pine weighs about 1.5 pounds.
3/8 = 3 ÷ 8 = .375 inches. Convert feet to inches by multiplying the number of feet by 12, since there are 12 inches in a foot. Using a feet to inches conversion calculator also simplifies this step. For example: 3 feet = 3 × 12 = 36 inches. Try our other length conversion calculators to convert other units to decimal inches.
8 Foot Saw Guide for Circular Saws – Durable Crosscut Guide for Making Perfectly Straight Cuts with Track Saws! ... Each Aluminum Saw Guide Track measures 4 feet long! Includes a BONUS cross cut track, so you can extend your Saw Guide even farther! ... This tool is a really simple design, which does not require "offsets." You mark your cut ...
S4S LUMBER UNIT SIZES S4S WIDE #PCS 2X4 13 208 2X6 8 128 2X8 6 96 2X10 5 80 31 extra rows. How lengthy is a 2×4 stud? The commonest dimensions of wall studs are 2-by-6 and 2-by-4. Wall studs for traditional partitions of 8 ft are 92 5/8 inches. In properties with 9-foot partitions, the studs are 104 5/8 inches.
Common: 2-in x 4-in x 8-ft; actual: 1.5-in x 3.5-in x 8-ft. Framing studs are ideal for a wide range of uses from framing of houses to basic interior structural applications. Every piece meets the highest grading standards for strength and appearance
Linear footage as referred to in wood or lumber is the length as you see it.For instance a 2 x 4 x 8, is 8 feet long. - In theoretical board feet this is actually 5.333 board feet or practically, 5.0 board feet. ( because a 2x4 is not really that dimension, but 1.5x3.5.
I have 2x8's on end spanning 12 feet. They've held up to some pretty good winds, probably similar to what you'll see in your afternoon thunderstorms but not what you will see in a hurricane. Will a 2x4 handle a 12 foot span? Not no how, not no way. Will they handle a 6 foot span? Probably, I'd even say yes.
taiguy. ·. Registered. 2016 3.6R Limited. Joined Feb 15, 2011. ·. 348 Posts. Discussion Starter · #1 · Aug 14, 2016. Pull the passenger seat all the way forward, lower the seat back, and then remove both headrests from front seat and rear seat - you've got enough flat storage space for 8 ft lumber.
The one I think may be the best is by sistering a 8 foot 2 x 4 or 2 x 6, whatever the wall is, to the existing 10 foot 2x. This creates the ledge to rest the floor joists for the loft. I will have a few walls under the loft that will run perpendicular to the loft joists that will support the center of the loft being my plan is 24 ft wide.
I set the posts for our chainlink in the back yard at 8 ft and it is a 5ft tall fence and I set the posts in concrete. The shadow-box privacy fence I built last year, is 6ft tall and I set the posts 10 ft. also in concrete. I don't think I would go 12ft on a horse fence. $.02. Mar 17, 2011.
Not that this makes any difference to us really, all three species are very similar. It does, however, explain the mysterious “SPF” label: S=Spruce, P=Pine, F=Fir. Another label you might find confusing on 2x lumber is the board length. Some 2x boards are cut to 96” (8 ft.)—while others curiously measure a couple inches shorter.
A 1x6, for example, actually measures 3/4" x 5 1/2". In this case, the planing is necessary for a smoother surface, so that the board could be used for interior applications. The length of the boards is generally exactly what you order, though we usually only stock pieces of even lengths. The usual lengths are 8', 10', 12', 14', and 16'.
2-in x 8-in x 8-ft Fir Lumber. Item # 432493 Model # WF208TOPCHC08. Common: 2-in x 8-in x 8-ft; Actual: 1.5-in x 7.25-in x 8-ft. Tight grain lumber with small knots that is resistant to cupping, twisting, and bowing. High quality lumber from the Inland …
This is actually a huge rack. It may not look as such on the photo but it’s almost 8 ft long by 4 ft high by 2 ft deep. We like the design and we've created a free building plan for it (see below). We've followed Jim and Susan's idea but with just one difference. We believe, on a 8-foot span, the 2x4s rails will eventually sag under the load.
You will notice that the larger sheds are much cheaper to build in terms of the cost per square foot. And in cases of going from 6 to 8 ft, 10 to 12 ft, 14 to 16 ft, and 18 to 20 ft in length it costs very little to build the next longer size. This is because certain sizes have a lot of waste and the next length up has very little or no waste.
Put together end-to-end, you have a support for a full 8-foot-long sheet of plywood. Some people build a single 8-by-4 frame, which is fine, too. I split it into two frames to make them easier to carry and store. If I were building another set of frames, I would make them a little smaller than 4-feet square, say, 44" on a side.
Hi everyone, my name is Stuart Morrison and I am the editor-in-chief and author of the Answeregy website. I am 35 years old and live in Miami, Florida. From an early age I loved to learn new things, constantly reading various encyclopedias and magazines. In 1998 I created my first Web site, where I posted interesting facts which you could rarely learn elsewhere. Then, it led me to work as a content manager for a large online publication. I always wanted to help people while doing something I really enjoyed. That's how I ended up on the Answeregy.com team, where I... Read more