preloader
  • Post:Stuart Morrison
  • 11/1/2021
  • Read 649
  • Share:

Are 882 sbc heads good?

Looking for an answer to the question: Are 882 sbc heads good? On this page, we have gathered for you the most accurate and comprehensive information that will fully answer the question: Are 882 sbc heads good?

The main difference between the 882 and 993 heads in regards to cracking is the 882 feeds the exhaust crossover from both center exhaust valves as opposed to the 993 which feeds the crossover from just one. That additional heat concentrated in the center of the head is the main reason for the cracking problem.


882's are the "Best" of the worst heads. They are the heavy weight casting. As noted, they are crack prone thru the center exhaust seats. They will flow fairly well if the intake side is port matched and the upper part of the exhaust port is blended.


Al Covin 's book CHEVY BY THE NUMBERS notes/verifies this oddity of the 881 & 882 Castings being excactly the same late in the 1974 year . Just sold an extra set of the good 2.02 /882 cast heads .


There are two different types of 882's - heavy and lightweight. The lightweight are crack prone, the heavy are not. If you want to only make 300hp, these heads will do it with some flat top pistons. The best factory heads are Vortec's that came on the last 350's, but they take a specific intake and centerbolt valve covers.

What is a Fuelie head?

It's two half-ovals connected by a straight bar-most easily described as "two humps." Some of these are also nicknamed "Fuelie" heads because a version appeared on fuel-injected 327-powered Chevy Corvettes. These heads appeared on 327 and 350 cubic inch engines across most of the 1960s (beginning in 1962).


What did 882 heads come on?

the 882 heads were installed on the 350ci and 400ci engines (400 heads had steam holes). The 882 heads had double heat-riser passage and were prone to cracking because they ran so hot. ... They were considered intermediate performance heads and had 76cc chambers.


How much HP will Vortec heads add?

Most of these small block Chevy heads offer a power increase of around 40 hp, and even the iron Vortec heads were worth 20 hp over stock. The two best small block Chevy heads in terms of peak horsepower were worth more than 60 hp.


How much power can Vortec heads make?

Jeff Smith: We wrote about Vortec heads in 2016, and that article spawned this question. The original answer was related to modifying the heads to accept more valve lift. Our original answer combined the Chevrolet Hot cam with a set of these Vortec heads. Our estimate then and now is around 350-375 horsepower.


Do you lose compression with aluminum heads?

Aluminum heads are said to drop between 1/2 and 1 full point of your effective compression because they draw more heat out of your combustion chamber (the one place you actually want some heat).


Can cylinder heads be too big?

“Super-sizing” may be a bit of an exaggeration, but cylinder head buyers have been known to opt for valves that are too large. That can result in cylinder heads that don't fit an engine's performance needs—or the actual engine itself!


Do aluminum heads make more power?

Aluminum heads will dissipate heat faster. This allows for higher Compression Ratios with less risk of Detonation. The cooler head also delivers a cooler air/fuel mixture to the combustion chamber. Cooler air is denser and can make more power.


Are aluminum heads better than cast?

Durability & Repair Both types of heads can be damaged if the engine overheats. Cast iron is much more durable. However, aluminum heads are easier to fix. The metal is softer and easier to weld and machine.


How much HP does new heads add?

Depending on your cam, you can gain anywhere from 40-70hp. Cam and heads can gain you 100+hp.


What heads should I put on my 350?

The more cubic inches the engine has, the more airflow the heads have to deliver. A head with 180 or 185cc intake runners will work well on a typical 350 Chevy street engine that makes 400 to 450 horsepower.


Which SBC heads are best?

Peak Torque and HorsepowerCylinder HeadPeak HorsepowerPeak TorqueDart419 at 6,200 rpm417 at 4,200 rpm (2)Jeg's408 at 5,900 rpm421 at 4,300 rpm (1)Summit405 at 5,900 rpm416 at 4,400 rpm (4)Edelbrock395 at 5,900 rpm409 at 4,200 rpm (5)•Jul 12, 2012


Are 441 heads any good?

441 heads are good flowing heads. You just have to calculate the amount to make them usable. That is the benefit of aftermarket heads. But I used them with a good piston to build compression and 2.02/1.60 valves and made about 465 hp out of a 355 with them.


Is it worth it to port and polish heads?

But for those of you who don't know, porting and polishing your heads is beneficial for power and efficiency of the engine. In a lot of cases, because of the increased CFM of the heads, as much as 30 horsepower is typical with good port work.


Do new cylinder heads increase horsepower?

Buying a new head that has four valves per cylinder will dramatically improve airflow in and out of the engine and this can improve power. Using performance cams can also make a big difference.


Why are Vortec heads so good?

0:524:17Vortec Heads - The Big Issues You Need To Know About - YouTubeYouTube


How much HP do ported heads add?

Porting the heads will definitely help airflow. You will gain 25 HP over the stock setup.


Are Vortec heads better than double hump heads?

Types of GM Vortec Heads The L31 Vortec heads have larger ports than the older Gen I cast steel heads, so they outflow the older heads. The Vortec heads are a little bit lighter than the older heads and have a “kidney” or “heart” shaped combustion chamber that is more efficient than the double hump chamber.


How much horsepower do Vortec heads add?

Most of these small block Chevy heads offer a power increase of around 40 hp, and even the iron Vortec heads were worth 20 hp over stock. The two best small block Chevy heads in terms of peak horsepower were worth more than 60 hp.


Where do 882 heads crack?

Premium Member. if it ran fine then run it, 882 heads usually crack when over heated in the exhaust seat area as Rick said, or or in-between intake and exhaust seats, and when they do there is evidence in the white exhaust from coolant in the exhaust. if the exhaust ports look uniform in color call it good and run it.


What's the difference between a Vortec 350 and a regular 350?

vortec 350s have a hydraulic roller cam, old 350s are flat tappet. the block is essentially the same but the heads are different. you need vortec specific intake manifolds, dunno about the headers. overall a vortec block will make more power with less money due to the heads, ported vortecs have a lot of potential.

Are 882 sbc heads good? Video Answer

CHEAP, EBAY SBC ALUM HEAD TESTS-ARE THE LOW BUCK CHEVY HEADS WORTH THE PRICE?

Are 882 sbc heads good? Expert Answers

Answeregy Expert
Troy ⭐ Answeregy Expert

Chevy Head Casting number 333882- Good or not? | Hot Rod Forum

none

Answeregy Expert
Nina ⭐ Answeregy Expert

882 heads any good? | Hot Rod Forum

search my post for heeelp mee and i talk about my 400 and my tale of woe.. 882's are a marginal head so good for a marginal street engine. i would say you'ld be okay as they have 1.94 intakes. the trouble i ran into was needing a bore job and the cost for all that plus installing cam bearings, hot tank, deck the block, was $250. the crank was shot too as the trust plate was gone and the …

Answeregy Expert
Averi ⭐ Answeregy Expert

882 sbc heads?? | Team Camaro Tech

Those heads (882) will make the power your after but they are junk, anytime you have a head that the heat cross over gets into both exhaust ports it not a good ideal, the 441 head would be a better choice. Im not real big on that cam either.

Answeregy Expert
Josephine ⭐ Answeregy Expert

Info on 882 heads.. | NastyZ28.com

882 heads are not as bad as some say, I have 390hp out of the motor in Kims wagon. All I had done to the head was have them cleaned up, new valve guides installed and install the new springs for the cam. Cant remember the mag, but I recall them saying something on how good the 882 heads are and they can be bought cheap. here is info

Answeregy Expert
Abbie ⭐ Answeregy Expert

Are 882 SBC heads good? - FindAnyAnswer.com

The 882 heads are smog heads from '74 to '80 and not very well regarded, but neither are stock '85 heads - if you can find out more about the 882's they may be better than your stock '85 heads - ie not only polished & ported but if milled so they will give higher compression and if …

Answeregy Expert
Mitzie ⭐ Answeregy Expert

882 Heads... Are they worth using? | The H.A.M.B.

There are two different types of 882's - heavy and lightweight. The lightweight are crack prone, the heavy are not. If you want to only make 300hp, these heads will do it with some flat top pistons. The best factory heads are Vortec's that came on the last 350's, but they take a specific intake and centerbolt valve covers.

Answeregy Expert
Juanita ⭐ Answeregy Expert

882 casting heads: Any good? | The H.A.M.B.

I recently bought a set of '882' casting sbc heads. Are these any good or 'better' than other stock heads? r raven, Oct 1, 2007. SHARE POST #1. Joined: Jul 10, 2006 Posts: 307. Profile Page. Zeke Fishburn. Member. from Houston, TX, USA, Erf (Earth) These are stock heads. ...

Answeregy Expert
Ivan ⭐ Answeregy Expert

SBC 882 heads? | The H.A.M.B. - The Jalopy Journal

Dan, I raced a '74 Corvette in NHRA Stock class, 350 w/#882 heads. The flow on the exhaust side is pretty poor, and the intake side is marginal at best. The heads have a tendency to crack, and are factory with 1.940 intake valves and 1.500 exhaust valves. Now, we blueprinted the heads to 63.3CC chamber size, and with all stock components and a ...

Answeregy Expert
Sylvester ⭐ Answeregy Expert

porting 882 sbc heads | Team Chevelle

those heads are great for nitrous and blower applications. they have one of the highest ascast ex flow and with some minor port and polish they flow assome on the ex side. I really cant answer on the intake side as I only ported the ex ports cause I used mine on a …

Answeregy Expert
Lukas ⭐ Answeregy Expert

Built 350 with 882 Heads, HP? | Team Chevelle

1,729 Posts. #4 · Aug 16, 2012. There is nothing wrong with the 882 heads as far as stock performance, and there have been many that run really well with them, of course you can't compare them to AFR, Brodix or Dart, but with a good valve job and some …

Answeregy Expert
Beverly ⭐ Answeregy Expert

882 SBC heads | Chevy Nova Forum - stevesnovasite.com

9 out of ten guys know the 882's aren't good for performance, but there's the always the one. He was the only guy who posted they were a "good, heavy weight head" and I don't think he meant heavy like good for anchoring boats.

Answeregy Expert
Jazzlyn ⭐ Answeregy Expert

400sbc, 882 heads. questions | S-10 Forum

4x4zr2GA said: yeah, sorry for the long post. shorter version: ill be getting a 400sbc that is .040 over, needs to honed and have a crank put in it. has dish pistons right now and 882 heads. the intake ports on the heads are MASSIVELY gargantuan. 76cc combustion chamber. i have two options: run a set of vortec heads on the 408 with the stock ...

Answeregy Expert
Harrison ⭐ Answeregy Expert

441 heads anygood? | Team Chevelle

according to a book i have on chevy small blocks they say the 441 is a very good head, good casting, and was basically the first step away from a high performance head with the increased chamber size (decreased compression). the same book says that if you buy an engine that has 882 heads they should be discarded. the book says they are a weak casting and not worth keeping. now having …

Answeregy Expert
Ina ⭐ Answeregy Expert

882 head or 041 head, which one to use? | Chevy Nova Forum

If you are dead set between those two sets of heads, then I would go with the 041 with hardened valve seats. Those 882 boat anchors have a nasty reputation of cracking on the exhaust valve seats because of the dual heat riser passage. 10 to 1 comp on the street is still pretty good. You just might have to add some 93 octane to the tank.

Answeregy Expert
Annette ⭐ Answeregy Expert

Race Car Engine Cylinder Head - Circle Track Magazine

203 cfm. GM 882 Iron The smallest of the GM heads we tested at only 151 cc, the 882, turned out to be the best-flowing of the early iron heads. This head was tested with the …

Answeregy Expert
Mark ⭐ Answeregy Expert

Eight Budget Small Block Chevy Heads Tested

The first thing we needed was a small block Chevy engine on which to evaluate power. Since this was a low-buck cylinder head test, we decided …

Answeregy Expert
Amilia ⭐ Answeregy Expert

350 CHEVY HEADS BEST AND WORST - YouTube

your building a budget small block chevy what heads should you be looking for and what to stay away fromsee part 2 http://youtu.be/q7unh0qkxey

Answeregy Expert
Belinda ⭐ Answeregy Expert

333882 garbage?? | Team Chevelle

Steer clear of the 624 and 882 heads at all costs. I have seen all SBC heads crack. For 76cc heads, the best thickest castings are 993, 339 and 336 487 and 441 heads are ok, but not as good as the ones mentioned above, IMO. And if you really want a good thick head that hardly ever cracks, the 185 is hard to beat.

Answeregy Expert
Tanner ⭐ Answeregy Expert

which heads 882 or 418 (305 heads) | The H.A.M.B.

HEATHENMemberfrom SIDNEY, NY. When I worked in a machine shop (mid '80s), it seems that a high percentage of the 882 heads that came to us failed the mag test. They're just large chamber smog heads, nothing special, so I wouldn't go out of …

Answeregy Expert
Russell ⭐ Answeregy Expert

Guide to Chevy Small-Block Production Heads - Chevy DIY

Head History. The selection list is basically rather thin for today’s performance engines. The earliest 265 and 283 small-blocks relied on an iron Power Pack head that featured 58-cc chambers and tiny 1.72/1.50-inch valves. The bigger heads to follow were the “double-hump” …

Answeregy Expert
Lola ⭐ Answeregy Expert

SBC head ? - Don Terrill’s Speed-Talk

Re: SBC head ? Post by NewbVetteGuy » Fri Sep 17, 2021 6:38 pm Are you thinking of the 882 heads vs. the 624 SMOG era heads? which were lightened / thinned versions of the 882 heads based upon what I've heard...

Answeregy Expert
Shirley ⭐ Answeregy Expert

Chevy Small Block Build - Mildly Amusing

Hardly exotic or even desirable by enthusiast standards, the 882 (common SBC smog era castings) heads featured both small valves (1.94/1.50) and large 76cc combustion chambers.

Answeregy Expert
Alison ⭐ Answeregy Expert

882 vs. 336 heads. | Off Road Vehicles

The 336 heads have been ported and polished, but not recently, they came off a monte carlo, that had a 350 supposedly built for the strip. One of the rocker arms in the head is broken. Is there any difference in valve springs and rocker arms between my current 882 heads and the 336? How are the 336 in general? would it be a good upgrade over my ...

Answeregy Expert
Elmira ⭐ Answeregy Expert

882 Chevy Heads Stage III 5 mod Roof to guide - YouTube

It would not be complete to not show the III.5 mode to IV without showing this guide mod. This is a major deal once you raise the roof as it will not let the...

Answeregy Expert
Geraldo ⭐ Answeregy Expert

883 heads, any good? | Team Chevelle

1,799 Posts. #4 · May 30, 2006. THose heads (882) are not very thick or strong castings and typically crack between the valves. I agree with Bill if they need any work or $$$ to make them work I would buy a different set of heads.

Answeregy Expert
Suzanne ⭐ Answeregy Expert

Speed Secrets: L82 Small Block Chevy Heads/Cam/Intake ...

Richard first installed a 350ci SBC on the Dyno. This particular small block is an L82, the performance 350 offered in the Corvette from 1973-1982, prior to the introduction of Chevys fuel injection engines. It featured a 9.0:1 compression ratio, cast iron 882 heads, and a Quadrajet induction system.

Answeregy Expert
Brenden ⭐ Answeregy Expert

1969 882 heads 350 bored 40 over lunati cam custom built ...

1969 Chevrolet motor bored 40 over lunati 501 lift cam 298 duration 760 carburetor double roller timing chain new oil pump Rings piston

Answeregy Expert
Vivien ⭐ Answeregy Expert

SBC Cylinder Head Info - Purple Sage Trading Post

- SBC Cylinder Head Info - I've compiled the following information on SBC Cylinder heads to help compare them. For the flow remember bigger is not always best. Some of the heads with large flows and big runners are not going to be good street heads, since they will have slow flow through the runners at …

Answeregy Expert
Jon ⭐ Answeregy Expert

Small Block Chevy Cylinder Head Identification

YEARS: CASTING# CID: Intake : Exhaust: CC : COMMENTS: 1971-75: 330545 : 307,350 : 1.72 : 1.5001 : 74 : 1971-73: 330862 : 400 : 1.94 : 1.5001 - 1971-76: 333881 : 350 ...

Answeregy Expert
Priscilla ⭐ Answeregy Expert

chevy 882 heads - YouTube

a quick porting on a 882 heads

Answeregy Expert
Diana ⭐ Answeregy Expert

Early SBC heads | irate4x4

882 heads at 76cc are bigger than what I have now (70cc). I don't want the CR to go down. It is looking like the 305 416 heads might be a good alternative as they have hardened seats, accessory holes, and are 58cc so compression should be up a point - hopefully, still within the realm of regular gas.

Answeregy Expert
Owen ⭐ Answeregy Expert

Free 882 and 487 sbc heads - NCC Forum Home Page

Status: Offline. Posts: 698. Date: Apr 27, 2012. Free 882 and 487 sbc heads. Permalink. Printer Friendly. I pulled these off my elky 350. In good shape, complete, just a little on the greasy side but clean inside. Free to good home.

Used Resourses:

About Author
Answeregy Author

Stuart Morrison

Hi everyone, my name is Stuart Morrison and I am the editor-in-chief and author of the Answeregy website. I am 35 years old and live in Miami, Florida. From an early age I loved to learn new things, constantly reading various encyclopedias and magazines. In 1998 I created my first Web site, where I posted interesting facts which you could rarely learn elsewhere. Then, it led me to work as a content manager for a large online publication. I always wanted to help people while doing something I really enjoyed. That's how I ended up on the Answeregy.com team, where I... Read more