preloader
  • Home >
  • Are
  • Are air water and steam all fluids?
  • Post:Stuart Morrison
  • 11/1/2021
  • Read 7894
  • Share:

Are air water and steam all fluids?

Looking for an answer to the question: Are air water and steam all fluids? On this page, we have gathered for you the most accurate and comprehensive information that will fully answer the question: Are air water and steam all fluids?

They are solid (ice), liquid (water) and gas (steam). This is theoretically true of all elements and compounds. Liquids and gases can be grouped together as Fluids. Fluids have common performance characteristics. For example, the flow of air in ducts and the flow of water in pipes are based on the same theory and equations.


Fluids have common performance characteristics. For example, the flow of air in ducts and the flow of water in pipes are based on the same theory and equations. The study of HVAC requires understanding gases (particularly Air) and liquids (particularly Water).


During the process, its temperature drops, but the fluid condensate remains at the same temperature. One pound of steam at a pressure of 30 psi gives up approximately 929 BTUs of heat. Steam gives up more energy per unit mass than water.


Fluid consists of both liquids and gases. Water comes under the category of liquid. Water is a fluid itself. Both liquids and gases comes under the category of fluids. Fluid is a caregory of matter and water is sub category of liquid

Is Jello a fluid?

Jello is both solid and liquid,” says Mr. ... “Jello is considered to be a colloid which means the solid gelatin protein is suspended in the water. It behaves more like a liquid because there are large spaces between the particles allowing your spoon to move through it easily.


Is steam a liquid?

I have been happily teaching that steam is still a liquid, which then becomes an invisible gas called water vapour.


Are all fluids liquids?

Fluids come along for liquids. All liquids are fluid. A fluid is a substance that lacks rigidity it cannot resist force when it is applied to it. Liquids can assume the shape of any container or vessel, and they are relatively incompressible.


What are fluids name two common fluids?

A substance which can flow is called fluid. The common fluids are juice, water, and soup.


Is milk a fluid?

Milk has been enjoyed throughout the world for thousands of years ( 1 ). By definition, it's a nutrient-rich fluid that female mammals produce to feed their young. The most commonly consumed types come from cows, sheep and goats. Western countries drink cow's milk most frequently.


Why can we see steam but not water vapour?

It can be formed either through a process of evaporation or sublimation. Unlike clouds, fog, or mist which are simply suspended particles of liquid water in the air, water vapour itself cannot be seen because it is in gaseous form. ... Steam often has droplets of water, which is what is seen water is boiling.


Are all liquids fluids?

Fluids come along for liquids. All liquids are fluid. A fluid is a substance that lacks rigidity it cannot resist force when it is applied to it. Liquids can assume the shape of any container or vessel, and they are relatively incompressible.


Is water a fluid?

Water is, by far, the most common liquid on Earth. The density of a liquid is usually close to that of a solid, and much higher than in a gas. Therefore, liquid and solid are both termed condensed matter. On the other hand, as liquids and gases share the ability to flow, they are both called fluids.


Can gasses be considered as fluids?

A gas fills its container, taking both the shape and the volume of the container. Liquids and gases are called fluids because they can be made to flow, or move.


Are air and water fluids?

Fluids can flow because the particles in fluids move past one another easily. You have probably heard the terms air pressure and water pressure. Air and water are both fluids. All fluids exert pressure.


What's the difference between water vapor and steam?

Water vapor is water as a gas, where individual water molecules are in the air, separate from each other. Steam is what you see above a boiling kettle. Steam is hot water in droplets almost big enough to see - but you can see the cloud of droplets.


What makes a fluid a fluid?

In physics, a fluid is a liquid, gas, or other material that continuously deforms (flows) under an applied shear stress, or external force. They have zero shear modulus, or, in simpler terms, are substances which cannot resist any shear force applied to them.


What's more powerful water or air?

Actually, water pressure is generally stronger than air pressure. ... If you pumped the air pressure up enough (like you do when you pump air into a bike tire), then the air pressure may become stronger than standard water pressure.


Do all fluids hydrate you?

You can stay fully hydrated throughout the day by drinking water and other fluids, as well as eating foods that are hydrating.


How is air and water different?

Air isn't very dense, it doesn't weigh much per volume. So the pressure falls off slowly as you go up. You have to go up a few kilometers before it drops to half the surface value. Water is much denser, so the pressure goes up faster as you go down.


Why steam is a liquid?

We learned that water has three states: ice is the solid state, water vapor is the gaseous state, and water is the liquid state. When water is heated it evaporates, which means it turns into water vapor and expands. At 100℃ it boils, thus rapidly evaporating. And at boiling point, the invisible gas of steam is created.


What is steam water?

Steam is the gas formed when water passes from the liquid to the gaseous state. At the molecular level, this is when H2O molecules manage to break free from the bonds (i.e. hydrogen bonds) keeping them together.


Is wet steam liquid or gas?

Wet steam is a mixture of steam and liquid water. It exists at a saturation temperature containing more than 5% water. It is said to be a two-phase mix: steam contains droplets of water that have not changed phase.


Are all liquids fluid?

Fluids come along for liquids. All liquids are fluid. A fluid is a substance that lacks rigidity it cannot resist force when it is applied to it. Liquids can assume the shape of any container or vessel, and they are relatively incompressible.


Is air a fluid or a gas?

Under normal conditions, matter exists as either a solid, a liquid, or a gas. Air is a gas. In any gas, we have a very large number of molecules that are only weakly attracted to each other and are free to move about in space.

Are air water and steam all fluids? Video Answer

Boiling, Atmospheric Pressure, and Vapor Pressure

Are air water and steam all fluids? Expert Answers

Answeregy Expert
Lyle ⭐ Answeregy Expert

Are air water and steam all fluids? – AnswersToAll

They are solid (ice), liquid (water) and gas (steam). This is theoretically true of all elements and compounds. Liquids and gases can be grouped together as Fluids. For example, the flow of air in ducts and the flow of water in pipes are based on the same theory and equations.

Answeregy Expert
Winston ⭐ Answeregy Expert

Is air water and steam all fluids? - Answers

none

Answeregy Expert
Arian ⭐ Answeregy Expert

Gases & Liquids (Fluids) and Solids: | Energy-Models.com

Gases & Liquids (Fluids) and Solids: The compound H 2 O (2 molecules of the element Hydrogen combined with 1 molecule of the element Oxygen) can exist in 3 states. They are solid (ice), liquid (water) and gas (steam). This is theoretically true of all elements and compounds. Liquids and gases can be grouped together as Fluids.

Answeregy Expert
Estelle ⭐ Answeregy Expert

Steam - the Energy Fluid | Spirax Sarco

The alternatives to steam include water and thermal fluids such as high temperature oil. Each method has its advantages and disadvantages, and will be best suited to certain applications or temperature bands. Compared to steam, water has a lower potential to carry heat, consequently large amounts of water must be pumped around the system to ...

Answeregy Expert
Christian ⭐ Answeregy Expert

Thermal Fluid vs. Steam - Comparison | Paratherm Heat ...

Steam systems are well known for corrosion problems. Air in combination with hot water, salts and other reactive contaminants presents an extraordinary potential for metal corrosion. Steam is abrasive and has virtually no lubricity. Add scale and deposits from minerals found in most all water supplies, and system problems quickly compound.

Answeregy Expert
Sandy ⭐ Answeregy Expert

Thermophysical Properties of Fluid Systems

Thermophysical Properties of Fluid Systems. Accurate thermophysical properties are available for several fluids. These data include the following: Please follow the steps below to select the data required. * Surface tension values are only available along the saturation curve.

Answeregy Expert
Jacquelyne ⭐ Answeregy Expert

Pros and Cons of Using Water and Steam as a Heating …

Steam also does not change state while it is used as a heating medium, and it gives up heat energy to the secondary medium. During the process, its temperature drops, but the fluid condensate remains at the same temperature. One pound of steam at a pressure of 30 psi gives up approximately 929 BTUs of heat. Steam gives up more energy per unit ...

Answeregy Expert
Buddy ⭐ Answeregy Expert

Fluid Heat Transfer Coefficients vs. Heat Exchanger ...

Average overall heat transmission coefficients for some common fluids and surface combinations as Water to Air, Water to Water, Air to Air, Steam to Water and more. The overall heat transfer coefficient is used to calculate total heat transfer through a wall or heat exchanger construction. The overall heat transfer coefficient depends on the ...

Answeregy Expert
Annabelle ⭐ Answeregy Expert

STEAM TABLES

STEAM TABLES. The following tables of the properties of steam are taken directly from Chapter 5.5.3 of the Heat Exchanger Design Handbook, 1986, by C. F. Beaton. The tables in this section are reprinted, with permission, from NBS/NRC Steam Tables. The reference state for all property values is the liquid at the triple point, for which state the ...

Answeregy Expert
Ryan ⭐ Answeregy Expert

What is the difference between fluid and water? - Quora

Answer (1 of 4): Fluid is the substance that flows which includes liquids and gases which can be separated i.e, the particles in it tend to move freely which is both compressible and in-compressible.Fluid lacks rigidity and have thickness or viscosity. For example: Nitrogen gas,honey,plasma Whe...

Answeregy Expert
Kyan ⭐ Answeregy Expert

Fluid Property Information - F-Chart

Fluid Property Information . EES provides built-in thermophysical property data for the fluids listed below. The fluids are grouped into Real Fluids, Ideal Gases, Brines, Incompressible Substances, and Mixtures (modelled as pseudo-pure substances)..Property data for air-water mixtures (psychrometrics) are provided by fluid AirH2O.

Answeregy Expert
Dessie ⭐ Answeregy Expert

Steam versus thermal fluid | Engineer Live

Furthermore, steam system infrastructure is far more intricate compared to thermal fluid applications. Safety valves, condensate return pumps, expansion joints, blow downs, chemical additions and drains all need to be correctly managed for the steam systems to run efficiently. Thermal fluid systems, on the other hand, only require a pump, an ...

Answeregy Expert
Evan ⭐ Answeregy Expert

Wet Steam vs. Dry Steam: The Importance of the Steam ...

The steam dryness fraction is used to quantify the amount of water within steam. If steam contains 10% water by mass, it's said to be 90% dry, or have a dryness fraction of 0.9. Steam dryness is important because it has a direct effect on the total amount of transferable energy contained within the steam (usually just latent heat), which ...

Answeregy Expert
Dewey ⭐ Answeregy Expert

TYPICAL OVERALL HEAT TRANSFER COEFFICIENTS (U - Isis …

Heaters Steam Water 1500 - 4000 Steam Organic solvents 500 - 1000 Steam Light oils 300 - 900 Steam Heavy oils 60 - 450 Steam Gases 30 - 300 Heat Transfer (hot) ... Air Cooled Exchangers Process Fluid U [W/m2 K] Water 300 - 450 Light organics 300 - 700 Heavy organics 50 - …

Answeregy Expert
Leidi ⭐ Answeregy Expert

Can we replace water to produce steam in generating ...

Answer (1 of 7): I have seen some research recently going into using supercritical CO2 as a working fluid. Steam has a lot, and I mean a lot of disadvantages to its operating in a system. CO2 is cleaner, cheaper, and much more resistant to contamination and corrosion than water. However, a sCO2 s...

Answeregy Expert
Monica ⭐ Answeregy Expert

How to use your plant’s steam, gas, air, or water to solve ...

Steam Steam Jet Exhausters Steam Jet Ejectors BULLETIN 4-E BULLETIN 5E-H Air/Gas Steam Jet Exhausters Steam Jet Ejectors BULLETIN 4-E BULLETIN 5E-H Liquid Liquid Jet Eductors Water Jet Exhausters BULLETIN 2-M BULLETIN 4-P Mix 2 materials Mixing chemicals in desired proportions Introducing water-treating compound into boiler feedwater

Answeregy Expert
Mercedes ⭐ Answeregy Expert

THERMODYNAMICS, HEAT TRANSFER, AND FLUID FLOW …

1.18 DETERMINE the change in the enthalpy of a fluid as it passes through a system component, given the state of the fluid at the inlet and outlet of the component and either steam tables or a Mollier diagram. 1.19 STATE the First Law of Thermodynamics. 1.20 Using the First Law of Thermodynamics, ANALYZE an open system including all

Answeregy Expert
Marco ⭐ Answeregy Expert

Steam Sterilization Principles & Common Mistakes Using ...

Direct steam contact with the surface of the object to be sterilized is required for the steam to transfer its stored energy to the object. Without direct steam contact to all surfaces, the item will not be sterilized. The amount of energy stored in steam is much higher than dry air or water at the same temperature.

Answeregy Expert
Harmony ⭐ Answeregy Expert

PROPERTY TABLES AND CHARTS (SI UNITS)

Table A–1 Molar mass, gas constant, and critical-point properties Table A–2 Ideal-gas specific heats of various common gases Table A–3 Properties of common liquids, solids, and foods Table A–4 Saturated water—Temperature table Table A–5 Saturated water—Pressure table Table A–6 Superheated water Table A–7 Compressed liquid water Table A–8 Saturated ice–water vapor

Answeregy Expert
Patti ⭐ Answeregy Expert

FLUID FLOW BASICS OF THROTTLING VALVES

Only two extensive properties of a fluid will locate the fluid in the physical universe. We know exactly where a fluid is when we say the fluid is — • saturated water at Psat = 29 psia = 2.0 BarA, we know that Tsat = 248.4°F = 120.1°C. • saturated steam at Tsat = 212°F = 100°C, we know that Psat = 14.7 psig = 1.013 BarA. SUPERHEATED ...

Answeregy Expert
Martha ⭐ Answeregy Expert

Fluid Property Information - F-Chart Software

Fluid Property Information . EES provides built-in thermophysical property data for the fluids listed below. The fluids are grouped into Real Fluids, Ideal Gases, Brines, Incompressible Substances, and Mixtures (modeled as pseudo-pure substances).Property data for air-water mixtures (psychrometrics) are provided by fluid AirH2O.

Answeregy Expert
Andre ⭐ Answeregy Expert

CHAPTER Utilities and Energy Efficient Design 3

† Steam is nontoxic, nonflammable, visible if it leaks externally, and inert to many (but not all) process fluids. Most sites have a pipe network supplying steam at three or more pressure levels for different pro-cess uses. A typical steam system is illustrated inFigure 3.2. Boiler feed water at high pressure is

Answeregy Expert
Dick ⭐ Answeregy Expert

(PDF) Thermodynamics Notes | s.m alghafri - Academia.edu

460mm2 For air, take R = 287 J/kg K and cp = 1005 J/kgoK o _____ Thermo level 1\Thermo & Fluids Module\Thermo & Fluids Module - Thermo Notes Book 2-Dec 07 23 John Withers - December 2007 STEAM TABLES (Thermodynamics\ Level 1\ Steam-tables.doc) CONSTANT PRESSURE HEATING OF WATER TO PRODUCE STEAM Temperature Superheated steam …

Answeregy Expert
Ellie ⭐ Answeregy Expert

What is Dry Steam - Definition - Thermal Engineering

Properties of Steam – Steam Tables. Water and steam are a common fluid used for heat exchange in the primary circuit (from surface of fuel rods to the coolant flow) and in the secondary circuit. It used due to its availability and high heat capacity, both for cooling and heating. It is especially effective to transport heat through vaporization and condensation of …

Answeregy Expert
Halie ⭐ Answeregy Expert

PROPERTIES OF STEAM AND WATER - Mass Engineers

none

Answeregy Expert
Lily ⭐ Answeregy Expert

thermodynamics - Why is steam a good working fluid for ...

Steam (gas-phase H 2 O) is very commonly used as the working fluid for external-combustion heat engines. It seems to me that it ought to be a poor choice, because:. Unless I am seriously confused about something, you have no choice but to throw the working fluid's heat of vaporization away every time around a Rankine cycle.

Answeregy Expert
Neal ⭐ Answeregy Expert

Why is water used as the working fluid in power stations ...

Its true we need to loose all that heat from the condensate leaving the turbine exhaust as we'll need to re-pump it and this is easier with water (or a dry saturated fluid) rather than steam (wet saturated). but even if you consider power generation where air is the working fluid (i.e. the Gas Turbine) you still won't see hot gas being ...

Answeregy Expert
Kamauri ⭐ Answeregy Expert

Thermophysical Functions - F-Chart

Whenever the substance name is spelled out (e.g., Steam (or Water), Nitrogen, R12, CarbonDioxide, Methane, etc.) the substance is modeled as a real fluid with subcooled, saturated, and superheated phases. Exceptions to this rule occur for Air and AirH2O, both of which are modeled as ideal gases.

Answeregy Expert
Winter ⭐ Answeregy Expert

CHAPTER 6 HEAT TRANSFER APPLICATIONS

The fluids can flow in the same direction through the equipment, ... There is the minimum of air with the steam in the jacket. 2. The steam is not superheated, as part of the surface must then be used as a de-superheater ... Steam Water, boiling Copper 1800 EXAMPLE 6.3. Steam required to heat pea soup in jacketed pan

Answeregy Expert
Toby ⭐ Answeregy Expert

Heat Transfer Coefficients Typical Values

Overall heat transfer coefficients are dependant on many parameters such as the nature of the fluid, fluid velocities, type of heat exchanger, temperatures and fouling. Despite all these determining parameters, typical overall heat transfer coefficients are available for common applications and fluids. If little information about the process and the parameters outlined …

Answeregy Expert
Kade ⭐ Answeregy Expert

Utility systems - processdesign

none

Answeregy Expert
Junior ⭐ Answeregy Expert

Water - Wikipedia

In almost all thermal power stations, water is used as the working fluid (used in a closed-loop between boiler, steam turbine, and condenser), and the coolant (used to exchange the waste heat to a water body or carry it away by evaporation in a cooling tower). In the United States, cooling power plants is the largest use of water.

Answeregy Expert
Lonnie ⭐ Answeregy Expert

Using the Thermodynamics Steam Table: Crucial Tool for ...

The steam table shown above is a saturated water and steam table. As all the other tables are used on the same principle we will only discuss this one. For an absolute pressure of 9 bars, the saturation temperature is 175.4 C. It means that at a temperature of 175.4 and above C all of the steam will be saturated.

Answeregy Expert
Dorene ⭐ Answeregy Expert

Differences between Thermal Fluid Heater and Steam Heaters

With thermal fluid heaters, the efficiency is known to be higher than with conventional steam systems.Flash losses in a typical steam system can be 6% to 14%. Add to that blowdown losses up to 3% and de-aerator losses of 2%. Clearly, the difference in the efficiency of the two systems is pronounced as thermal fluid systems do not suffer any of …

Answeregy Expert
Erick ⭐ Answeregy Expert

What is the difference between air and evaporated water ...

That means, the first two gases, N X 2 and O X 2, make up 99.0 % of the atmosphere by volume. It also has some low level Ozone ( O X 3) and under ambient conditions, has varying quantity of water vapor as well (as clouds in the sky). That water vapor in air comes from different sources such as steam water, water evaporated from sea bed, etc.

Answeregy Expert
Keegan ⭐ Answeregy Expert

ME 200 Thermodynamics 1 Fall 2017 – Exam 3

3. [40 points] A solar-powered steam power plant uses the sun’s radiation to boil water. At peak operating conditions, the rate of radiation heat transfer into the boiler is 420 MW. The working fluid is water/steam, with data at each state provided in the table below; all …

Answeregy Expert
Denisse ⭐ Answeregy Expert

Appendix C: Heat Exchanger Design - Wiley Online Library

Water-to-air in finned tubes (water in tubes) 5–10 (air); 70–150 (water) Steam-to-air in finned tubes (steam in tubes) 5–50 (air); 70–705 (water) Introduction to Thermo-Fluids Systems Design, First Edition. Andre G. McDonald and Hugh L. Magande.´ 2012 AndrC e G. McDonald and Hugh L. Magande. Published 2012 by John Wiley & Sons, Ltd.´

Answeregy Expert
Meg ⭐ Answeregy Expert

Convective Heat Transfer Coefficients Table Chart ...

Cold Fluid : Hot Fluid : Overall U (BTU/hr-ft 2-F) Water : Steam (pressure) 350 -750 : Water : Steam (vacuum) 300 – 600 : Water or brine : Organic solvent (saturated, atmospheric) 100 – 200 : Water or brine : Organic solvent ( atmospheric, high non-condensables) 20 – 80 : Water or brine : Organic solvent (saturated, vacuum) 50 – 120 ...

Answeregy Expert
Sanford ⭐ Answeregy Expert

Paper 2 SET B - aipnpc.org

a) All of the below b) Air locking Water hammer d) Steam locking 38. For flash steam calculation, flash steam quantity available depends upon a) Total heat of flash steam b) Steam pressure c) Steam enthalpy at atmospheric pressure d) Condensate pressure and flash steam pressure 39.

Answeregy Expert
Brett ⭐ Answeregy Expert

Mech302-HEAT TRANSFER HOMEWORK-8 Solutions …

Mech302-HEAT TRANSFER HOMEWORK-8 Solutions 3. (Problem 8.53 in the book) Heated air required for a food-drying process is generated by passing ambient air at 20 C through long, circular tubes (D = 50 mm, L = 5 m) housed in a steam condenser.

Answeregy Expert
Iva ⭐ Answeregy Expert

Power Plant Filtration – Power Generation | Pall Corporation

Without effective filtration solutions, fluid cleanliness cannot be controlled and steam/gas systems are unable to operate at peak efficiencies. Combined cycle power plant customers around the world rely on Pall products to purify water, …

Answeregy Expert
Brenden ⭐ Answeregy Expert

Paper 2 Set A 19th NATIONAL CERTIFICATION …

c) Water hammer d) All of the above 15. For flash steam calculation, flash steam quantity available depends upon a) Condensate pressure and flash steam pressure b) Steam pressure c) Steam enthalpy at atmospheric pressure d) Total heat of flash steam 16. Air venting in a steam system is required because air is _____. a) A good conductor b) An ...

Answeregy Expert
Amir ⭐ Answeregy Expert

Central Heating System - an overview | ScienceDirect Topics

The most common centralized heating systems in both residential and commercial spaces typically involve using a flame to heat and move a heat transfer fluid via forced hot air, pumped hot water, or steam delivery. 4 As per Krigger and Dorsi, these centralized oil, gas, and/or propane heating systems mix and burn fuel in a combustion chamber, and the heat from the flame and …

Answeregy Expert
Elinor ⭐ Answeregy Expert

Overall Heat Transfer Coefficient Table Charts and ...

K = Surrounding fluid area Temperature It is used in calculating the heat transfer, typically by convection or phase transition between a fluid and a solid. The heat transfer coefficient has SI units in watts per squared meter kelvin: W/(m 2 K).

Answeregy Expert
Arya ⭐ Answeregy Expert

Flue gas properties table - Pipe Flow Calculations

download the calculator close. This table is for flue gases. It gives values of some physical properties - density and viscosity in relation to the temperature of gases. It is for following chemical composition: nitrogen N 2 - 76%. carbon dioxide CO 2 - 13%. water vapor H 2 O - 11%.

Answeregy Expert
Aubrey ⭐ Answeregy Expert

FACULTY NAME: AMIT KUMAR ASSISTANT PROFESSOR …

Q 5: The power developed by a turbine in a certain steam plant is 1200 kW. The heat supplied to the steam in the boiler is 3360 kJ/kg, the heat rejected by the system to cooling water in the condenser is 2520 kJ/kg and the feed pump work required to pump the condensate back into the boiler is 6 kW. Calculate the steam flow round the cycle in kg/s.

Answeregy Expert
Georgina ⭐ Answeregy Expert

What is Rankine Cycle - Steam Turbine Cycle - Definition

The basic operation of the steam turbine is similar to the gas turbine except that the working fluid is water and steam (with a phase change) instead of air or gas. Properties of Water and Steam Water and steam are a common fluid used for heat exchange in the primary circuit (from surface of fuel rods to the coolant flow) and in the secondary ...

Answeregy Expert
Hester ⭐ Answeregy Expert

Chapter 7 Vapor and Gas Power Systems - CPP

We will consider the Rankine cycle with water as the working fluid. Process 1-2: Assuming that bulk kinetic and potential energy and heat transfer are negligible, the power produced by the turbine is given by W t = m (h 1-h 2) (7.1-1) In this equation m is the mass flow rate of the working fluid. If the steam enters as a

Answeregy Expert
Alexiz ⭐ Answeregy Expert

Waste Heat Recovery Methods And Technologies - Chemical ...

A more costly and efficient system will use steam generation followed by air preheating. In addition to steam generation, economizer coils can be added to heat water or intermediate heat transfer fluids. Saturated steam generated in the steam generators can be super heated by recovering heat from fluegases or hot streams.

Used Resourses:

About Author
Answeregy Author

Stuart Morrison

Hi everyone, my name is Stuart Morrison and I am the editor-in-chief and author of the Answeregy website. I am 35 years old and live in Miami, Florida. From an early age I loved to learn new things, constantly reading various encyclopedias and magazines. In 1998 I created my first Web site, where I posted interesting facts which you could rarely learn elsewhere. Then, it led me to work as a content manager for a large online publication. I always wanted to help people while doing something I really enjoyed. That's how I ended up on the Answeregy.com team, where I... Read more